Malco

Malco A50 Carbide Tip Scriber

0 out of 5

Carbide Tipped Scriber with retractable point

$22.68

Hot

Malco A60 Adjustable Sheet Metal Scriber

0 out of 5

Measure, mark, and scribe trim lines on sheet metal in one easy operation. Set the desired trim depth on the scriber extension and tighten the knob. The stop at the end of the scriber sleeve glides along the edge of work as a 6 x 3/8ﾔ sheet metal screw point scribes a clean, hard-line. Adjustable from 1/4ﾔ to 12-1/2ﾔ (6.4 to 318 mm) depths in 1/8? (3.2 mm) graduations. Rotate the scriber extension and knob end to end for depths larger than 6-1/2ﾔ(165 mm). The use of a Zip-In sheet metal screw makes point replacement practical and economical. The screw point is protected when the tool is closed. Pocket size tool is constructed of rust-resistant nickel-plated steel. Knob assembly with hardened steel bolt insert will not strip out.

$19.56

Malco AV1 Aviation Snip (Left Cutting)

0 out of 5

Malcoﾒs AV Aviation Snips feature POWER-FITﾙ performance hand grips that increase productivity and distributes pressure evenly, which results in less user fatigue. Non-slip grooves and safety guards also help users achieve a Maximum grip in some of the dirtiest conditions. An easy release side latch offers quick operation and cutting on the job. Made with only the best, the hardened forged steel jaws offer a strong long lasting cutting edge.

$17.45

Malco AV2 Aviation Snip (Right Cutting)

0 out of 5

$17.45

Malco AV3 Aviation Snip (Left or Right Cutting)

0 out of 5

$17.45

Malco AV6 Aviation Snip (Offset Left Cutting)

0 out of 5

$22.47

Malco AV7 Aviation Snip (Offset Right Cutting)

0 out of 5

$22.47

Malco AV8 Aviation Snips - Left Cutting Vertical

0 out of 5

The forged steel jaws of these left-cutting snips are set at a 90-degree angle to allow easy gripping when cutting sheet metal in tight spaces or overhead.

$27.44

Malco AV9 Aviation Snips - Right Cutting Vertical

0 out of 5

The forged steel jaws of these left-cutting or right -cutting snips are set at a 90-degree angle to allow easy gripping when cutting sheet metal in tight spaces or overhead. The operator can follow tight circular or square pattern left or right cuts with either a pushing or pulling motion. A serrated edge on the upper jaw and compound head-to-handle linkage provide powerful, non-slip leverage for cutting up to 24-gauge (0.61 mm) cold rolled steel or 28-gauge (0.38 mm) stainless. Handles feature non-slip, cushion inserts, torsion-spring action and a squeeze-open, side operated latch. Rust-resistant polished forged steel jaws and black oxide finished handle stampings promote long service life.

$27.44

Malco C4R Redline 9 in. Downspout Crimper

0 out of 5

If you are looking for a tool that efficiently downsizes the corners of aluminum or steel downspout, then the Malco 5 Blade Gutter Crimper is the tool you are looking for. The blades produce 1-1/4 inch (31.75mm) long double crimps without causing deformation of downspout walls. A factory-like crimp ensures the downspout walls stay square for a tight fitting, leak-proof connection. A handle closing stop helps to maintain a consistent crimp profile. Made with hardened all-steel construction and a nickel chrome finish, you can be assured this tool will last a long time.

$43.52

Malco C5A2 Crimping Tool for Sheet Metal - TurboCrimper IMPACT

0 out of 5

Quickly makes your impact driver a power crimper for 30-24 ga. (0.41-0.71 mm) round metal duct and (0.31-0.61 mm) stove pipe. The extra power of the TurboCrimper, is five times faster than manual sheet metal crimpers, making your job a lot easier.

$166.86